Я новичок в программировании Verilog.Я пытаюсь собрать 8-битный Carry Lookahead Adder как шаг к созданию 64-битного CLA.В основном, как я это реализовал, я использую 2 4-битных "блока" CLA для создания 8-битного CLA.Я предоставлю свой код, а затем объясню возникшую проблему.
Код ниже:
// 4-BIT CLA CODE
module CLA4Bit(A, B, carryIn, carryOut, PG, GG, Sum);
input[3:0] A, B;
input carryIn;
output carryOut;
output PG;
output GG;
output[3:0] Sum;
wire[3:0] G, P, C;
assign G = A & B;
assign P = A ^ B;
assign Sum = P ^ C;
assign C[0] = carryIn;
assign C[1] = G[0] | (P[0] & C[0]);
assign C[2] = G[1] | (P[1] & G[0]) | (P[1] & P[0] & C[0]);
assign C[3] = G[2] | (P[2] & G[1]) | (P[2] & P[1] & G[0]) | (P[2] & P[1] & P[0] & C[0]);
assign PG = P[3] & P[2] & P[1] & P[0];
assign GG = G[3] | (P[3] & G[2]) | (P[3] & P[2] & G[1]) | (P[3] & P[2] & P[1] & G[0]);
endmodule
// 8-BIT CLA CODE BELOW
module CLA8Bit(A, B, carryIn, carryOut, Sum);
// 8-bit wire for the inputs A and B
input[7:0] A, B;
// Wire for the ORIGINAL carry-in
input carryIn;
// Wire for the carryOut
output carryOut;
// Wire that carries the Sum of this CLA
output[7:0] Sum;
// Wires for the propagate of the first 4-bit block (p3)
// and the second (p7)
wire p3, p7;
// Wires for the generate of the first 4-bit block (g3)
// and the second (g7)
wire g3, g7;
// Wires for the carry of the first block (c3) and the
// second (c7)
wire c3, c7;
// The two 4-bit CLA blocks that make up the 8-bit CLA
CLA4Bit block1(A[3:0], B[3:0], carryIn, c3, p3, g3, Sum[3:0]);
CLA4Bit block2(A[7:4], B[7:4], c3, c7, p7, g7, Sum[7:4]);
endmodule
Я написал базовый тестовый стенд для тестирования своего кода:
module CLA_TB();
// TEST THE 8-BIT CLA
// Inputs
reg[7:0] A;
reg[7:0] B;
reg carryIn;
// Outputs
wire carryOut;
wire[7:0] Sum;
wire PG;
wire GG;
// Instantiate the 8-bit CLA
CLA8Bit CLA8BitDUT (
.A(A),
.B(B),
.carryIn(carryIn),
.carryOut(carryOut),
.Sum(Sum)
);
// Initialize the testbench signals
initial
begin
// Start with the carryIn set to 0
assign carryIn = 0;
// The standard first test. Set
// A = b0000 0001 and B = b0000 0001
// Answer should be Sum = b0000 0010
assign A = 8'b00000001;
assign B = 8'b00000001;
#20
// Next, set A = b0001 1011 and
// B = b1101 0111. Answer should
// be Sum = b1111 0010 = hF2.
assign A = 8'b00011011;
assign B = 8'b11010111;
#20
// Finally, try setting the carryIn
// to 1 and then test A = b0111 1011
// and B = b1101 0011. Answer should be
// Sum = 0100 1111 w/ overflow carry
assign carryIn = 1'b1;
assign A = 8'b01111011;
assign B = 8'b11010011;
#20
$finish;
end
endmodule
Так что проблема в моих симуляциях тестового стенда (яиспользуйте ModelSim), первые 4 бита суммы (которые соответствуют первому 4-битному экземпляру CLA в 8-битном модуле CLA) задаются как X на странице Wave.Вторые 4 бита добавляются просто отлично.
Проведя некоторое исследование, я обнаружил, что X отображаются в Verilog, когда в проводе имеется более одного драйвера (источник сигнала?).Однако я не вижу места, где бы я отправлял более одного сигнала в мой первый 4-битный экземпляр CLA в 8-битном модуле CLA.Кроме того, если что-то подобное было причиной, то я не знаю, почему этого не произойдет и со вторым набором из 4 битов, поскольку оба 4-битных CLA настроены очень похоже.
Почему это происходит?